Glass Flake Coating and Lining System

Product Details:

MIPROGLASS glass flake filled coatings & linings are formulated from high purity, chemical resistant glass flake, premium quality resins and other special additives & fillers. The combination of high performance resins & glass flakes produce coatings & linings with outstanding performance characteristics, which can be applied by brush, trowel and spray.

Product Details:

A series of intermediate to heavy duty linings (or coatings) which can be applied to steel and offer long term protection against corrosion and physical abuse.These systems consist of a toweled applied base coat over a primer coat and followed by glass filled top coats to achieve excellent chemical resistance, exceptionally low permeation and high physical properties for over all performance of lining & coating. Each of the Mipro Glass 201 linings is reinforced with glass flakes up to 0.4mm (1/64 in maximum Dimension by 3-4 microns thick, which lie parallel to the substrate thereby offering ex-resistance to permeation, corrosion, abrasion, physical abuse and thermal shock. Mipro glass 201 series coatings will withstand total immersion at temperatures up to 70 C, a temperatures up to 150 C.The recommended thickness of the mipro glass 201 linings is 1mm to 3mm and this is two or more coats by trowel application. Plus Top coat by brush, roller or air less spray.
matt/cloth reinforcement is also possible for higher strength.

Mipro glass 201 series linings are formulated from different high performance resins:

• MIPROGLASS 201 - I Isophthalic polyester
• MIPROGLASS 201 - B Bisphenol polyester
• MIPROGLASS 201 - V Vinyl ester
• MIPROGLASS 201 - SV Vinyl ester  superior grade
• MIPROGLASS 201 - E Epoxy
• MIPROGLASS 201 - E (HYB) Hyb. Epoxy

Practical Coverage:

Application:

Please request Surface Preparation and Installation Data sheets for specific advice.

Cure:

Cure times will vary with ambient temperatures and quantity of catalyst used. Typically the Mipro glass 201 series can be over coated within 4 to 6 hours and are hard in 8 to 12 hours. The coating will not be fully cured until about 72 hours after application but can go into light duty service after 24 hours.

 

 

Additional Information:

• Item Code: 201

Product Details:

A series of medium duty polyester, vinyl ester, Epoxy resin base coating designed to protect steel and
concrete work against atmospheric corrosion and the exterior surfaces of tanks and process plant against the splashing and spillage of chemicals. Each of the Mipro Glass 101 coatings is reinforced with properly graded glass flakes, which lie parallel to the substrate thereby offering excellent resistance to permeation, corrosion, abrasion, physical abuse and thermal shock. Mipro glass 101 (I, B, V series coatings will withstand gas temperatures up to 120 C, and can be used in immersion service at ambient temperatures. All the mipro glass 101 series coatings can be applied by brush or by spray, they are approx. 90-100% solids, and cure at ambient temperature. The recommended thickness is approx. 400-500 microns and this is obtained in one primer and two to four coats depending on different application environment.

Mipro glass 101 series linings are formulated from one of these 5 high performance resins:

• MIPROGLASS 101 I Isophthalic polyester
• MIPROGLASS 101 B Bisphenol polyester
• MIPROGLASS 101 V Vinyl ester
• MIPROGLASS 101 SV Vinyl ester – superior grade
• MIPROGLASS 101 E Epoxy
• MIPROGLASS 101 E (HYB) Hyb. Epoxy

Chemical Resistance:

For information on the chemical resistance of each of these grades please contact Chemiprotect
Engineers Corrosion Resistance Guide, under the appropriate code letter.

Practical Coverage:

General Information:

• % solids by volume of theoretical 98% at time of mixing. Practical typically 80% 5%. All Vinyl/polyester resin systems are subject to monomer loss and material Shrinkage during application and curing.
• In microns per coat dry is 180-200
• Recommended cleaner is cleanser No.1 cleaning only, thinning not recommended.
• Overcoating times is indefinitely over coatable (if clean and dry)
• Shelf life is 4-6 months at 25⁰c.

Additional Information:

• Item Code: 101